STMicroelectronics MDmesh™ II Power MOSFETs
The STMicroelectronics MDmesh™ II Power MOSFETs associates
a vertical structure to STM's strip layout to yield one of the
industry's lowest levels of on-resistance and gate charge, making it
suitable for the most demanding high efficiency converters. These MDmesh™ II Power MOSFETs
are fully insulated, have a low profile package with increased creepage
path from pin to heatsink plate. They are 100% avalanche tested and
feature low input capacitance, gate charge, and gate input resistance.
STMicroelectronics Zener-Protected SuperMESH3™ Power MOSFETs
The STMicroelectronics new SuperMESH3™ Power MOSFETs are obtained through the combination of a further fine tuning of ST's well established strip-based PowerMESH™ layout with a new optimization of the vertical structure. In addition to reducing on-resistance significantly down, special attention has been taken to ensure that these MOSFETs have a very good dynamic performance coupled with a very large avalanche capability for the most demanding switching applications. SuperMESH3™ Power MOSFETs now come in voltages up to 1200V.
STMicroelectronics Low-Power High Accuracy Operational Amplifiers
STMicroelectronics Low-Power, High Accuracy, Operational Amplifiers are single versions and offer low voltage operation with rail-to-rail output swing. The LMV82x series outperforms the industry standard LMV321 especially with regard to the gain bandwidth product (5.5 MHz). The TSV85x series outperforms the industry standard LMV321, proposing lower supply voltage capability, enhanced input offset voltage and smaller packages. Typical applications for these include battery powered and portable devices, signal conditioning, active filtering and medical instrumentation.
STMicroelectronics TS3011 Rail-to-Rail High-Speed Comparators
STMicroelectronics' TS3011 Rail-to-Rail High-Speed Comparators feature a high-speed response time with rail-to-rail inputs. Specified for a supply voltage of 2.2 to 5 V, these comparators can operate over a wide temperature range of -40°C to +125°C. The TS3011 offers micropower consumption as low as a few hundred microamperes, thus providing an excellent ratio of power consumption current versus response time. Typical applications for these include telecom, instrumentation, signal conditioning, high-speed sampling systems and portable communication systems.
STMicroelectronics STM32100B-MCKIT Motor Control Starter Kit
STMicroelectronics STM32100B-MCKIT Motor Control Starter Kit is an integrated system designed to provide a complete, ready-to-use motor control application developed around the STM32F100 microcontroller. This starter kit is particularly suited to drive three-phase brushless permanent magnet synchronous motors and demonstrates how effectively the low-cost STM32F100 microcontrollers can be used in cost optimized real-world motor control applications. The STM32100B-MCKIT supports Field Oriented Control (FOC) drive of three-phase permanent magnet synchronous motors (PMSM). Single-shunt resistor current measurement is supported out-of-the-box allowing closed loop torque control. Position measurement can be implemented using quadrature encoder sensors, Hall effect sensors or sensorless algorithms.
STMicroelectronics STM32F051x ARM® Cortex™-M0 32-Bit MCUs
STMicroelectronics STM32F051x ARM® Cortex™-M0 32-Bit MCUs family incorporates the high-performance ARM Cortex™-M0 operating at a 48 MHz frequency, high-speed embedded memories (Flash memory up to 64 Kbytes and SRAM up to 8 Kbytes), and an extensive range of enhanced peripherals and I/Os. All devices offer standard communication interfaces (up to two I2Cs, two SPIs, one I2S, one HDMI CEC, and up to two USARTs), one 12-bit ADC, one 12-bit DAC, up to five general-purpose 16-bit timers, a 32-bit timer and an advanced-control PWM timer. These features make the STM32F051xx microcontroller family suitable for a wide range of applications such as application control and user interfaces, handheld equipment, A/V receivers and digital TV, PC peripherals, gaming and GPS platforms, industrial applications, PLCs, inverters, printers, scanners, alarm systems, video intercoms, and HVACs.
STMicroelectronics STC3105 Battery Monitor IC Alarm
The STMicroelectronics STC3105 Battery Monitor IC Alarm includes the hardware functions required to implement a low cost gas gauge for battery monitoring. The STC3105 Battery Monitor IC Alarm uses accurate measurements of the battery voltage to estimate a battery's state-of-charge (SOC). The STC3105 Battery Monitor IC Alarm uses a low cost sense resistor to precisely sense the charge or discharge states, detect light-load conditions without ambiguity for voltage measurements, and accurate SOC calculation. The STMicroelectronics STC3105 Battery Monitor IC Alarm features 0.5% accuracy battery voltage monitoring, low battery alarm output with programmable thresholds, and small 3x2 mm. package.
STMicroelectronics STLDC08 Step-Up Controller for LED Supply
STMicroelectronics' STLDC08 Step-Up Controller for LED Supply is optimized to operate from one or two NiCd/NiMH or alkaline cells. The STLDC08 Step-Up Controller is able to drive an external MOSFET (N-channel) enabling it for use with wide power levels. With hysteretic control on STMicroelectronics' STLDC08 Step-Up Controller, it eliminates the need for small signal control loop compensation. The STLDC08 Step-Up Controller for LED Supply integrates a FET driver for a precise PWM dimming. Typical applications include single/dual cell NiMH, NiCd, or alkaline batteries, small appliances LED lighting and portable lighting.
STMicroelectronics STM65xx Smart Reset™ ICs
STMicroelectronics STM65xx Smart Reset ICs offer a safe, convenient and intuitive means of resetting 'frozen' gadgets, such as mobile phones, media players, and other portable consumer devices. Traditionally, when electronic devices freeze or lock up, users would either try to remove the battery, which is not always convenient, or find an appropriate tool to press the dedicated reset button placed in a hole that is often difficult to access. STM65xx Smart Reset ICs extend the functional capability of the existing buttons so that users can simply re-set their frozen device with a long push of one or two buttons simultaneously, depending on the device configuration. With the increasing popularity of touch-screen devices, STMicroelectronics STM65xx Smart Reset ICs remove the need for extra buttons, saving space and cost for the equipment manufacturers, and significantly increasing convenience for the user.
STMicroelectronics Sound Terminal® 2.1-Channel Digital Audio System
STMicroelectronics Sound Terminal® 2.1-Channel Digital Audio System is an integrated solution embedding digital audio processing, digital amplification, FFX™-power output stage thereby creating a high-power single chip FFX™ solution comprising high-quality, high efficiency, and all digital amplification. These Sound Terminal® 2.1-Channel Digital Audio Systems are part of the Sound Terminal® family and provides full digital audio streaming from the source to the speaker, offering cost effectiveness, low power dissipation and sound enrichment. FFX™ (Fully Flexible Amplification) is the evolution of the STMicroelectronics ternary technology: the advanced processor is available for ternary, binary and binary differential implementations, a subset of the full capability of the FFX™ processor.
STMicroelectronics ARM® Cortex™-M3 Based STM32 F2 Series MCU
The STMicroelectronics' ARM® Cortex™-M3 Based STM32 F2 Series MCU is built on ST's advanced 90 nm NVM process technology with the innovative adaptive real-time memory accelerator (ART Accelerator™) and the multi-layer bus matrix offering an unprecedented price/performance trade-off. These ARM® Cortex™-M3 Based STM32 F2 Series MCUs are characterized by a high degree of integration combining up to 1 Mbyte of Flash memory and up to 128 Kbytes of SRAM with Ethernet MAC, USB 2.0 HS OTG, camera interface, and hardware encryption support and external memory interface. STMicroelectronics' acceleration technology enables these MCUs to achieve up to 150 DMIPS at 120 MHz FCPU which is equivalent to zero wait state execution, while keeping the dynamic current consumption at the outstandingly low level of 188 µA/MHz.
STMicroelectronics M24LRx Dual Access Protocol RF EEPROM-EXPANSION
STMicroelectronics has expanded their offering of Dual Access Protocol RF EEPROM family of memories which provides the flexibility to remotely program or update electronic products anytime during their lifetime and anywhere in the supply chain. These new Dual Access Protocol RF EEPROMs now offer a 16Kbit memory size that was not available in the M24LR64-R series. The STMicroelectronics Dual Access Protocol RF EEPROM can be accessed either by a standard I²C interface or by an ISO 15693 RF interface. This M24LR16E family is optimized for use in a variety of applications, including medical equipment, industrial equipment, factory and building automation, computers/peripherals, and consumer electronics.
The STMicroelectronics M24LR64-R Dual Access Protocol RF EEPROM family of memories provides the flexibility to remotely program or
update electronic products anytime during their lifetime and anywhere in the supply chain. The EEPROM memory bank of the STMicroelectronics M24LR64-R can be accessed either by a standard I²C interface or by an ISO 15693 RF interface. The ISO 15693 RF interface is based on a passive RFID technology that does not require a battery or power to operate but instead gets the energy and data stream from the RF reader. This STMicroelectronics Dual Access Protocol EEPROM family is based on two industry-standard interfaces and features a unique and flexible data protection scheme that protects some or all of the information contained in the memory. The M24LR64-R family is optimized for use in a variety of applications, including medical
equipment, industrial equipment, factory and building automation, computers / peripherals, and consumer electronics.
View the entire M24LR Series
STMicroeletronics Wide Band Directional Coupler with ISO Port
STMicroelectronics Wide Band Directional Couplers with ISO Port are designed to measure RF antenna or cell phone transmission output power in GSM/WCDMA/TD-SCDMA applications. These Wide Band Directional Couplers have been customized for wide-band operating frequencies (EGSM and CELL, PCS, DCS, TD-SCDMA, WCDMA Band I) with less than 0.2 dB insertion losses in the transmit bandwidth. Typical applications for STMicroelectronics Wide Band Directional Couplers include multi-band equipment such as power amplifier modules, front end modules, GSM/WCDMA mobile phones, quad band power amplifier modules and quad band front end modules.
HSP061-8M16 8-Line ESD Protection - STMicroelectronics
STMicroelectronics HSP061-8M16 is an 8-channel ESD array with a rail to rail architecture designed specifically for the protection of high speed differential lines. The HSP061-8M16 8-Line ESD Protection for High Speed Lines has an ultra-low variation of the capacitance that ensures very low influence on signal-skew. The large bandwidth and the low reflection make it compatible with 3.4 Gbps. STMicroelectonics HSP061-8M16 8-Line ESD Protection for High Speed Lines is designed to protect against electrostatic discharge on sub micron technology circuits driving HDMI 1.3 and 1.4, Digital Video Interface, Display Port and Serial ATA.
STMicroelectronics LSM320DL Linear Sensor Modules
STMicroelectronics LSM320DL Linear Sensor Modules are system-in-package devices featuring a 3D digital accelerometer and a 2D digital gyroscope. STMicroelectronics LSM320DL Linear Sensor Modules have a dynamic user selectable full-scale acceleration range of ±2g/±4g/±8g/±16g and and angular rate of ±250/±500/±2000 deg/sec. The accelerometer and gyroscope sensors can be either activated or put in low power/power-down mode separately for application optimized power saving. The STMicroelectronics LSM320DL is ideal for use in a variety of applications, including GPS navigation systems, impact recognition and logging, and gaming and virtual reality input devices.
STMicroelectronics SPV1020 Interleaved DC-DC Boost Converter
The STMicroelectronics SPV1020 Interleaved DC-DC Boost Converter is a monolithic device designed to maximize the power generated by photovoltaic panels independently of temperature and amount of solar radiation. The optimized of the power conversion is obtained with an embedded logic that performs that MPPT (maximum power point tracking) algorithm on the PV cells connected to the converter. One or more converters can be housed in the connection box of PV panels, replacing the bypass diodes. The maximum power point is locally computed, providing a higher efficiency at system level than one of the conventional topologies. The STMicroelectronics SPV1020 DC-DC Boost Converter embeds the power MOSFETs for active switches and synchronous rectification, minimizing the number of external devices. The switching frequency of the SPV1020 is internally generated, set by default at 100kHz, and is externally tunable. The duty cycle can range from 5% to 90% with a step of 0.2%.
STMicroelectronics SPV1001N30 Cool Bypass Switch
STMicroelectronics SPV1001N30 Cool Bypass Switch is a system-in-package solution for photovoltaic applications to perform cool bypass rectification similar to that of a conventional Schottky diode but with much lower forward voltage drop and reverse leakage current. The STMicroelectronics SPV1001N30 Cool Bypass Switch consists of a power MOSFET transistor which charges a capacitor during the OFF time and drives its gate during the ON time using the charge previously stored in the capacitor. The ON and OFF times are set to reduce the average voltage drop across the drain and source terminals, resulting in reduced power dissipation. The SPV1001N30 features an operating junction temperature of 150ºC and comes in a 5x6mm PQFN package.
STMicroelectronics LSM330DLC Linear Sensor Modules
STMicroelectronics LSM330DLC linear sensor modules are system-in-package devices featuring a 3D digital accelerometer and a 3D digital gyroscope. STMicroelectronics LSM330DLC linear sensor modules have a dynamic, user-selectable full-scale acceleration range of ±2g/±4g/±8g/±16g and an angular rate of ±250/±500/±2000 deg./sec. The accelerometer and gyroscope sensors can be either activated or put in low-power / power-down mode separately for power-saving optimized applications. STMicroelectronics LSM330DLC linear sensor modules are ideal for use in a variety of applications, including GPS navigation systems, impact recognition and logging, gaming and virtual reality input devices, and more.
STMicroelectronics STEF05 / STEF12 Electronic Fuses
STMicroelectronics STEF05 / STEF12 Electronic Fuses come in 3 x 3mm IC packages, which can replace larger conventional fuses or other protection devices such as transils or diodes. Unlike regular fuses, STEF05 / STEF12 Electronic Fuses do not cut the power suddenly or require replacement after actuating, thereby helping to improve equipment uptime and availability while also reducing maintenance costs. Compared to transils or diodes, STEF05 / STEF12 Electronic Fuses enable versatile and simple programming of protection parameters. Applications for STMicroelectronics STEF05 / STEF12 Electronic Fuses include hard disk drives, solid state drives, arrays, and DVD and Blu-ray disc drivers.
STMicroelectronics TSV619x CMOS Op Amps
STMicroelectronics TSV619x CMOS operational amplifiers are a family of single and dual op amps offering low voltage, low power operation, and rail-to-rail input and output. STMicroelectronics TSV6191 / TSV6191A single and TSV6192 / TSV6192A dual op amps also feature an ultra-low input bias current as well as a low input offset voltage. TSV619x op amps have a high gain bandwidth product of 450kHz while consuming only 10µA at 5V. They must be used in a gain configuration (equal or above +4 or -3). These features make the STMicroelectronics TSV619x family ideal for sensor interfaces, battery supplied and portable applications, and active filtering.
STMicroelectronics TDA7498 BTL Class-D Audio Amplifiers
STMicroelectronics TDA7498 BTL Class-D Audio Amplifiers comprise dual (TDA7498 / TDA7498L) and mono (TDA7498MV) devices with single power supply. These STMicroelectronics devices are designed for home systems and active speaker applications. STMicroelectronics TDA7498 Class-D Audio Amplifiers come in a 36-pin PowerSSO package with exposed pad (EPU) to facilitate mounting a separate heatsink. The TDA7498 and TDA7498MV feature 100W + 100W output power at THD=10% with RL=6Ω and VCC=36V and 80W + 80W output power at THD=10% with RL=8Ω and VCC=34V. The TDA7498L features 80W + 80W output power at THD=10% with RL=6Ω and VCC=32V and 70W + 70W output power at THD=10% with RL=8Ω and VCC=34V.
STMicroelectronics STTS2002 2.3V Memory Module Temperature Sensor
STMicroelectronics STTS2002 2.3V Memory Module Temperature Sensor features an integrated 2KB SPD EEPROM and an operating temperature range of -40ºC to +125ºC. STMicroelectronics STTS2002 Memory Module Temperature Sensor is targeted for DIMM modules in mobile personal computing platforms, servers, and other industrial applications. The digital temperature sensor has a programmable 9-12 bit analog-to-digital converter (ADC) that monitors and digitizes the temperature to a resolution of up to 0.0625ºC. The temperature sensor in the STMicroelectronics STTS2002 is specified for operating at supply voltages from 2.3V to 3.6V. Operating at 3.3V, the typical supply current is 160µA.
STMicroelectronics L6520 / L6521 Low Voltage Smart Ballast Controllers
STMicroelectronics L6520 and L6521 Low Voltage Smart Ballast Controllers are the first highly integrated ballast controllers able to drive both MOSFETs and Bipolar Junction Transistors (BJTs), providing all the necessary protections to ensure maximum reliability of the applications in compliance with major safety and power consumption regulations. STMicroelectronics L6520 and L6521 Smart Ballast Controllers replace more expensive MOSFETs without comprising performance. These STMicroelectronics devices allow you to quickly design ballast with any kind of lamp topology/size/power without limitations. L6520 and L6521 Smart Ballast Controllers feature very accurate oscillator precision in a wide operating temperature range. These devices are designed for use in electronic ballasts and integrated CFLs.
STMicroelectronics ALTAIR04-900 All-Primary-Sensing Switchers
STMicroelectronics ALTAIR04-900 All-Primary-Sensing Switchers feature primary side constant voltage operations with no optocoupler. The STMicroelectronics ALTAIR04-900 combines a high-performance low-voltage PWM controller chip and a 900V avalanche-rugged power section in the same package. These STMicroelectronics All-Primary-Sensing Switchers provide quasi-resonant valley switching operation and low standby consumption. ALTAIR04-900 switching regulators are designed for use in AC-DC adapters, SMPS for energy metering, and auxiliary power supplies for 3-phase input industrial systems.
STMicroelectronics STM8SVLDISCOVERY STM8S Value Line Evaluation Board
The STMicroelectronics STM8SVLDISCOVERY STM8S Value Line Evaluation Board helps you discover the features of STM8S Value Line Microcontrollers and develop your own application. The STM8SVLDISCOVERY includes everything required for beginners and users to get started quickly.The STMicroelectronics STM8SVLDISCOVERY Evaluation Board is built around an STM8S003T6 MCU but allows evaluation of the main features of all STM8S Value Line MCUs. The eval board includes an ST-LINK embedded debug tool. The STM8SVLDISCOVERY plugs into a PC through a standard USB cable.
STMicroelectronics MP34Dx01 MEMS Audio Sensor Digital Microphones
STMicroelectronics MEMS Audio Sensor Digital Microphones are ultra-compact, low-power, omnidirectional devices built with a capacitive sensing element and an IC interface. The sensing element, capable of detecting acoustic waves, is manufactured using a specialized silicon micromachining process dedicated to producing audio sensors. These devices have an acoustic overload point of 120 dBSPL with a best on the market 62.6 dB or 63 dB signal-to-noise ratio and -26 dBFC sensitivity. The MEMS Audio Sensor Digital Microphones comes in an SMD-compliant package and operates over an extended temperature range from -30ºC to +85ºC. This STMicroelectronics MEMS Audio Sensor Digital Microphones are ideal for use in a variety of applications, including mobile terminals and VoIP, laptop and notebook computers, and portable media players.
STMicroelectronics DPIULC6-6DJL DisplayPort™ ESD Protection ICs
STMicroelectronics DPIULC6-6DJL DisplayPort™ ESD Protection ICs deliver enhanced protection for PCs, monitors, projectors, and similar equipment featuring the latest DisplayPort interface, the next-generation successor to traditional VGA and DVI connections. The STMicroelectronics DPIULC6-6DJL provides essential protection for the sensitive DisplayPort circuitry against electrostatic discharges (ESD) that could damage or destroy the display device. STMicroelectronics has optimized the protection to meet the different needs of the main and auxiliary data channels defined in the DisplayPort Vesa 1.1a standard. DPIULC6-6DJL ESD protection ICs are capable of blocking hazardous voltage spikes but are also effectively transparent to the high-speed data signals, allowing them to pass virtually undistorted at the highest possible speed and power to ensure consistent high-quality multimedia experiences for users.
STMicroelectronics STY112N65M5 MDmesh™ V Power MOSFETs
STMicroelectronics STY112N65M5 MDmesh™ V Power MOSFETs are N-channel devices with industry-leading maximum RDS(on) (<0.022Ω). STMicroelectronics STY112N65M5 MDmesh V Power MOSFETs feature innovative proprietary vertical process technology and STMicroelectronics PowerMESH™ horizontal layout structure. The excellent switching performance of the STY112N65M5 makes it ideal for applications requiring superior power density and outstanding efficiency.
STMicroelectronics TDA2005 20W Bridge / Stereo Amplifiers
STMicroelectronics TDA2005 20W bridge / stereo amplifiers are Class B dual audio power amplifiers in a Multiwatt11 package designed specifically for car radio applications. Power booster amplifiers can be designed easily using the STMicroelectronics TDA2005, which provides a high current capability (up to 3.5A) and can drive very low impedance loads (down to 1.6Ω in stereo applications) obtaining an output power of more than 20W (bridge configuration).
STMicroelectronics STM32F4DISCOVERY High-Performance Discovery Board
STMicroelectronics STM32F4DISCOVERY STM32F4 high-performance discovery board helps you discover the high-performance features of STM32 F4 High-Performance Cortex™-M4 microcontrollers. The STMicroelectronics STM32F4DISCOVERY allows for easy development of applications and includes everything required for beginners and experienced users to get started quickly. The discovery board is based on the STM32F407VGT6 and includes an ST-LINK/V2 embedded debug tool, two ST MEMS/sensors -- digital accelerometer and digital microphone, an audio DAC with integrated class D speaker driver, LEDs and push buttons, and a USB OTG micro-AB connector.
STMicroelectronics L3GD20 Motion Sensor 3-Axis Digital Gyroscopes
STMicroelectronics L3GD20 motion sensor 3-axis digital gyroscopes are housed in a 4x4x1mm package and combine high-sensing resolution with outstanding immunity to audio noise and vibrations, making motion-sensing user interfaces more realistic in mobile phones, tables, game consoles, and other smart consumer devices. The L3GD20 features resonant frequency above the audio bandwidth, allowing it to operate with greater accuracy and reliability. These STMicroelectronics 3-axis digital gyroscopes have an advanced design with a single sensing structure for motion measurement along all three orthogonal axes, further increasing sensing accuracy and reliability and guaranteeing excellent output stability over time and temperature. The STMicroelectronics L3GD20 offers a wide set of user-programmable full-scale ranges from ±250 degrees per second up to ±2000 degrees per second, with the low full-scale values for high accuracy of slow-motion sensing and the high range to detect and measure very fast gestures and movements.
STMicroelectronics STEVAL-MKI113V1 LSM303DLM Adapter Board
The STMicroelectronics STEVAL-MKI113V1 adapter board is designed to facilitate evaluation of the LSM303DLM digital compass. The STMicroelectronics STEVAL-MKI113V1 adapter board offers an effective solution for fast system prototyping and device evaluation directly within the user's application. The STEVAL-MKI113V1 can be plugged into a standard DIL24 socket. The adapter provides the complete LSM303DLM pinout and comes ready-to-use with the required decoupling capacitors on the VDD power supply line. The pinout of the adapter is fully compatible with all other adapter boards, making it possible to easily switch from one sensor to another during device evaluation without the need for board redesign.
STMicroelectronics LSM303DLM Next Generation Digital Compass
The STMicroelectronics LSM303DLM Next Generation Digital Compass is an ultra-low-power device that provides advanced navigation and location-based services in portable consumer applications by integrating high-resolution three-axis sensing of linear and magnetic motion in a 5x5x1mm package. The STMicroelectronics LSM303DLM sensor module provides extremely accurate output across full-scale ranges of ±2g/±4g/±8g (linear acceleration) and from ±1.3 up to ±8 gauss (magnetic field). This digital compass device boasts state-of-the-art stability over time and temperature and a 30% increase in magnetic sensing resolution over its predecessor, the LSM303DLH. The module is pin-to-pin and software-compatible with the previous-generation device. The LSM303DLM is ideal for use in a wide variety of applications, including compensated compass, map rotation, position detection, free-fall detection, and more.
STMicroelectronics M41T62LC6F Serial Real-Time Clock with Alarm
The STMicroelectronics M41T62LC6F Serial Real-Time Clock is the industry's smallest RTC with embedded crystal saves space and battery life in portable electronics. The M41T62LC6F integrated RTC/crystal measures only 3.2x1.5mm and offers ultra-low power consumption. The STMicroelectronics M41T62LC6F RTC is ideally suited to the needs of battery-power designs. By operating at low voltages from 1.3 to 4.4V, this RTC can be driven directly from an Li-ion battery and draws only 350nA.
STMicroelectronics STLA02 White LED Driver for Display Backlight
The STMicroelectronics STLA02 White LED Driver for Display Backlight is capable of driving 6 white LEDs in series. The STMicroelectronics STLA02 is a synchronous boost converter with high-side control that operates from a 2.5 to 18V input voltage and can provide an output voltage up to 27V. The output current of up to 20mA is set using an external resistor. The EN pin allows this white LED driver to be switched on and off. The EN pin is also dedicated for PWM dimming of the output current. The STMicroelectronics STLA02 is ideal for use in PDAs and other handheld devices, cell phones, and MP3 players.
STMicroelectronics EMIF06-MSD03F3 EMI Filter / ESD Protection Device
STMicroelectronics EMIF06-MSD03F3 EMI Low-Pass Filter / ESD Protection device is highly integrated and based on IPAD™ technology. The STMicroelectronics EMIF06-MSD03F3 offers ESD protection to comply with the IEC standard and EMI filtering to reject mobile phone frequencies. This STMicroelectronics device is designed for use in Micro (T-Flash) secure digital memory cards in mobile phones and communication systems.
STMicroelectronics HDMI2C1-5DIJ ESD Protection / Signal Booster
The STMicroelectronics HDMI2C1-5DIJ ESD Protection and Signal Booster for HDMI™ 1.3 Tx Control Links is a fully integrated ESD protection, level-shifting device and signal booster for control links of HDMI 1.3 transmitters. The STMicroelectronics HDMI2C1-5DIJ ESD Protection and Signal Booster is a bi-directional isolation buffer, integrating hysteresis and signal boosters for maximum system robustness and signal integrity. All these features are provided in a single 16-lead QFN package featuring straightforward routing. The HDMI2C1-5DIJ is a simple plug-and-play device that provides HDMI designers with an easy way to gain full compliance with the stringent HDMI 1.3 CTS on a wide temperature range.
STMicroelectronics STPS60SM200C 200V Power Schottky Rectifiers
STMicroelectronics STPS60SM200C 200V Power Schottky Rectifiers are new high-voltage devices that will help increase the energy efficiency and ruggedness of equipment such as telecom base stations and welding equipment. STMicroelectronics STPS60SM200C Power Schottky Rectifiers are optimized for use in high-current AC/DC power supplies delivering normal DC output voltages in the 30V-50V range. Its 200V maximum reverse voltage is compatible with known worst-case operating conditions and provides the design margins needed to withstand over-voltages and remain fully operational down to -40C, making it ideal for telecom base station sites anywhere in the world. The STPS60SM200C integrates two interconnected diodes in a three-pin package to provide a more energy efficient alternative to ultra-fast diodes, which typically have higher conduction losses. These STMicroelectronics Power Schottky Rectifiers achieve over 2kV ESD-protection, which is higher than comparable Schottky devices tested according to IEC 61000-4-2.
STmicroelectronics STM32 F4 High-Performance Cortex™-M4 MCUs
STMicroelectronics STM32 F4 32-bit Cortex™-M4 Microcontrollers (MCUs) open the door to the digital signal controller (DSC) market with a family of devices that are pin-to-pin and software compatible with the STM32 F2 series but with better performance, DSP capability, more SRAM, and peripheral improvements such as full duplex I²S, less than 1μA RTC, and 2.4MSPS ADCs. STMicroelectronics STM32 F4 MCUs include a floating point unit and core features such as built-in single-cycle multiply-accumulate (MAC) instructions, optimized SIMD arithmetic, and saturating arithmetic instructions. The adaptive realtime ART Accelerator™ combined with STMicroelectronics 90 nm technology provides linear performance up to 168MHz, unleashing the full performance of the core. These features expand the number of addressable applications in the industrial, consumer, and healthcare segments. STM32 F4 series MCUs include devices with 512KB to 1MB of on-chip Flash memory, 192KB of SRAM, and 15 communication interfaces.
STMicroelectronics DMOS Dual Full Bridge Drivers
STMicroelectronics DMOS Dual Full Bridge Drivers are designed for motor control applications and are realized in BCDmultipower technology, which combines isolated DMOS power transistors with CMOS and bipolar circuits on the same chip. These DMOS Dual Full Bridge Drivers include two independent constant OFF time PWM current controllers that perform the chopping regulation. STMicroelectronics DMOS Dual Full Bridge Drivers features thermal shutdown and a non-dissipative overcurrent detection on the high side power MOSFETs.
STMicroelectronics SPV1001 Cool Bypass Switch for Photovoltaic Applications
The STMicroelectronics SPV1001 Cool Bypass Switch is a system-in-package solution for photovoltaic applications to perform cool bypass rectification similar to that of a conventional Schottky diode but with much lower forward voltage drop and reverse leakage current. This STMicroelectronics analog solar power switch consists of a power MOSFET transistor that charges a capacitor during the OFF time and drives its gate during the ON time using the charge previously stored in the capacitor. The ON and OFF times are set to reduce the average voltage drop across the drain and source terminals, resulting in reduced power dissipation. The STMicroelectronics SPV1001 Cool Bypass Switch is designed for use in photovoltaic panels.
STMicroelectronics Utra-Fast Planar 600V HF IGBTs
STMicroelectronics STGWA45HF60WDI ultra-fast W series planar 600V IGBTs improve the power efficiency in high-frequency equipment by minimizing turn-off energy losses mainly at frequencies up to 100kHz. STMicroelectronics STGWA45HF60WDI 45A planar 600V IGBTs facilitate parallel connection for higher power levels as a result of the VCE(sat) classification. These STMicroelectronics ultra-fast 600V IGBTs also achieve up to 10% better performance in conduction and switching losses and lower spread of dynamic parameters even at high temperature compared to previous generation devices. The STGWA45HF60WDI is designed for use in welding, induction heating, solar inverters, UPS, PFC, and resonant converters.
STMicroelectronics STCS1A 1.5A Max Constant Current LED Drivers
STMicroelectronics STCS1A 1.5A max constant current LED drivers are designed to provide a precise constant current starting from a varying input voltage source. STMicroelectronics STCS1A LED drivers replace discrete components for driving LEDs in low voltage applications such a 5V, 12V, or 24V, providing benefits in precision, integration, and reliability. The STCS1A provides up to 40V input voltage and less than 0.5V voltage overhead. These STMicroelectronics devices are designed for LED constant current supplying for varying input voltages, low voltage lighting, small appliance LED lighting, and car LED lights.
STMicroelectronics EVL250W-ATX80PL 250W ATX SMPS Demo Board
The STMicroelectronics EVL250W-ATX80PL 250W ATX SMPS Demo Board offers an advanced SMPS architecture designed for high-end switching converters dedicated to PC power supplies, servers, and all-in-one solutions. The architecture of the EVL250W-ATX80PL is based on an innovative L6563S front-end PFC stage, an L6591 high-efficiency asymmetrical half-bridge converter stage, two L6727 compact DC-DC post regulators, and an auxiliary low consumption VIPER27 flyback converter. This STMicroelectronics demo board features very high overall efficiency. The multiple output configuration is compliant with the 80 PLUS® Silver level of efficiency while the single output configuration outperforms the 80 PLUS Gold level of efficiency.
STMicroelectronics STEVAL-ILM001V1 Plug-In Hardware Module for STM8S-DISCOVERY
The STMicroelectronics STEVAL-ILM001V1 plug-in hardware module for the STM8S-DISCOVERY is used to create a fully functioning DALI (Digital Addressable Lighting Interface) slave application. The STEVAL-ILM001V1 plug-in hardware module + STM8S-DISCOVERY can be connected to and controlled by any DALI network. The STMicroelectronics STEVAL-ILM001V1 provides all the functions required by the DALI standard. The DALI standard is a communication protocol widely used in intelligent lighting applications.
STMicroelectronics LIS3DH 3-Axes Nano Accelerometer
The STMicroelectronics LIS3DH ultra low-power high performance three axes nano accelerometer features digital I²C / SPI serial interface standard output. The LIS3DH three axes accelerometer features ultra low-power operational modes that allow advanced power saving and smart embedded functions. The STMicroelectronics LIS3DH accelerometer has dynamically user selectable full scales of ±2g / ±4g / ±8g / ±16g and is capable of measuring applications with output data rates from 1 Hz to 5 kHz.
Learn More
STMicroelectronics STM32L-DISCOVERY STM32L Ultralow Power Discovery Board
The STMicroelectronics STM32L-DISCOVERY STM32L ultralow power discovery board demonstrates the ultralow power features of STM32L microcontrollers and lets you develop and share your applications. The STMicroelectronics STM32L-DISCOVERY ultralow power discovery board is based on an STM32L152RBT6 MCU and includes an ST-Link/V2 embedded debugging tool interface, an LCD (24 segments, 4 commons), LEDs, pushbuttons, a linear touch sensor, or touchkeys. The board power supply is through USB bus or an external 3.3 or 5V supply voltage. This STMicroelectronics discovery board also includes two pushbuttons (user and reset) and and one linear touch sensor or four touchkeys.
STMicroelectronics STM32F103xF / STM32F103xG Performance Line MCUs
STMicroelectronics STM32F103xF / STM32F103xG XL-density STM32 Performance Line microcontrollers incorporate the high-performance ARM Cortex™-M3 32-bit RISC core operating at 72MHz, high-speed embedded memories (Flash memory up to 1MB and SRAM up to 96KB), and an extensive range of enhanced I/Os and peripherals connected to two APB buses. All STM32F103xF / STM32F103xG Performance Line MCUs offer three 12-bit analog-to-digital converters, 10 general-purpose 16-bit timers plus two PWM timers, and standard and advanced communication interfaces (up to two I²Cs, three SPIs, two I²Ss, one SDIO, five USARTs, an USB and a CAN). The STMicroelectronics STM32F103xx XL-density Performance Line family operates in the -40 to +105°C temperature range from a 2.0 to 3.6V power supply A comprehensive set of power-saving modes allows the design of low-power applications. The STM32F103xx family is suited for use in a variety of applications, including motor drives, application control, medical and handheld equipment, PC and gaming peripherals, GPS platforms, industrial applications, PLCs, inverters, printers, scanners, alarm systems, and video intercom.
STMicroelectronics STM32F101xF / STM32F101xG Access Line MCUs
STMicroelectronics STM32F101xF / STM32F101xG XL-density STM32 Access Line microcontrollers incorporate the high-performance ARM Cortex™-M3 32-bit RISC core operating at a 36MHz frequency, high-speed embedded memories (Flash memory up to 1MB and SRAM of 80KB), and an extensive range of enhanced I/Os and peripherals connected to two APB buses. All STMicroelectronics STM32F101xF and STM32F101xG MCUs offer a 12-bit analog-to-digital converter, 10 general-purpose 16-bit timers, and standard and advance communications interfaces (up to two I²Cs, three SPIs, and five USARTs). The STM32F101xF / STM32F101xG XL-density Access Line operates in the -40 to +85ºC temperature range from a 2.0 to 3.6V power supply. A comprehensive set of power-saving mode options allows the design of low-power applications. STM32F101xx XL-density MCUs are suited for use in a wide range of applications medical and handheld equipment, PC peripherals and gaming, GPS platforms, industrial applications, PLC, printers, scanners
alarm systems , power meters, and video intercom.
STMicroelectronics TS4982 2W Stereo Audio Power Amplifier
The STMicroelectronics TS4982 audio power amplifier features a stereo loudspeaker driver and a ground-referenced stereo headphone driver. An independent standby mode pin allows the STMicroelectronics TS4982 audio power amplifier to simultaneously drive both output drivers. The TS4982 operates on a single 5V supply and delivers 2W (typ.) output power into a 4Ω load at 1% THD+N. This STMicroelectronics amplifier features a PC beep input, three levels of 3D stereo enhancement, and 4-step gain control. The TS4982 is ideal for laptop / notebook computers and portable audio devices.
STMicroelectronics STM32L EnergyLite™ 32-bit Microcontrollers
STMicroelectronics STM32L EnergyLite™ 32-bit microcontrollers combine unique STMicroelectronics low-leakage 130nm process technology and optimized power-saving architecture to deliver industry-leading energy-saving performance. STM32L ARM Cortex-M3 based MCUs are part of the STMicroelectronics EnergyLite platform of ultra low-power products enabling designers to optimize performance, function, and battery life and meet efficiency-related criteria such as eco-design targets. STM32L MCUs consume only 9µA at 32kHz in low power mode and 230 µA/MHz in dynamic run mode. The STM32L151 and STM32L152 differ in that the STM32L152 features an LCD controller. These ARM Cortex-M3 EnergyLite MCUs are well suited for a wide range of applications, including medical and handheld equipment, application control, user
interface, PC peripherals, gaming, GPS, sports equipment, alarm systems,
wired and wireless sensors, video intercom, and utility metering.
STMicroelectronics ECMF02-2AMX6 / ECMF04-4AMX12 Common Mode Filter ICs
STMicroelectronics ECMF02-2AMX6 and ECMF04-4AMX12 are the industry's first silicon-based ICs to combine common mode filtering and ESD protection needed by high-speed data lines. STMicroelectronics ECMF02 and ECMF04 common mode filter / ESD protection ICs enable manufacturers to reduce part counts and simplify design of reliable, high-speed data circuits commonly used in smartphones, tablets, and mobile computers as well as wired connections such as USB2.0 and HDMI. The ECMF02-2AMX6 is a single-channel device while the ECMF04-4AMX12 is a two data-channel device. Both STMicroelectronics ICs feature 6 GHz differential bandwidth that complies with HDMI, MIPI D-PHY, and USB2.0. These common filter / ESD protection devices also provide high common mode attenuation, high ESD protection with low remaining voltage (Vpeak <50V), and flow-through pin-out for efficient, simplified PCB layout.
STMicroelectronics Power MOSFETs
STMicroelectronics offers a variety of new high-performance N-channel power MOSFETs. The STmicroelectronics STD8N65M5 and STP8N65M5 are N-channel 650V, 0.56Ω, 7A MDmesh™ V power MOSFETs. The STD8N65M5 comes in a DPAK package while the STP8N65M5 comes in a TO-220. The STL17N3LLH6 is an N-channel 30V, 17A STripFET™ VI DeepGATE power MOSFET that exhibits the lowest on-resistance in a standard package. The STMicroelectronics STL85N6F3 N-channel, 60V STripFET™ 2 power MOSFET shows extremely high packing density for low on resistance, rugged avalanche characteristics, and low gate charge. The STP34NM60N N-channel second generation MDmesh MOSFET features low input capacitance and gate charge, making it suitable for the most demanding high efficiency converters.
STMicroelectronics LCP12 Protection ICs for Ringing SLICs
STMicroelectronics LCP12 protection ICs for ringing SLICs protect SLICs operating on both negative and positive battery supplies as well as high voltage SLICs. STMicroelectronics LCP12 protection ICs provide crowbar mode protection for both TIP and RING lines. The surge suppression is assumed for each wire by two thyristor structures, one dedicated to positive surges, the second one for negative surges. These STMicroelectronics protection ICs feature a wide firing voltage range (-120V to +120V) and are ideal for a variety of applications, including dual battery supply voltage SLICs, digital subscriber line access multiplexers, and digital loop carriers.
STMicroelectronics ACST12xx / ACST10xx Triac Switches
STMicroelectronics ACST12xx and ACST10xx triacs belong to the ACS™ / ACST power switch family built with application specific discrete technology. ACST12xx and ACST10xx overvoltage protected AC switches are triacs with overvoltage crowbar technology. STMicroelectronics ACST12xx and ACST10xx triacs embed a triac structure and a high voltage clamping device able to absorb the inductive turn-off energy and withstand line transients such as those described in the IEC 61000-4-5 standard. The ACST1210-7 and ACST1010-7 need a low gate current to be activated and still provides a high electrical noise immunity complying with the IEC 61000-4-4 standard. The ACST1235-7 and ACST1035-7 offer an extremely high static dV/dT immunity of 2 kV/µs minimum.
STMicroelectronics LIS331HH Series Sensors and Adapter Board
STMicrolectronics' LIS331HH Series MEMS digital output motion sensors are ultra low-power, high performance full-scale three-axes "nano" accelerometers that offer wide supply voltage from 2.16 V to 3.6 V. STMicroelectronics' LIS331HH sensors have dynamically user selectable full scales (±6g/±12g/±24g) and are capable of measuring accelerations with output data rates from 0.5 Hz to 1kHz, allowing the user to check the functioning of the sensor in the final application. These sensors contain two independent interrupt engines able to recognize dedicated inertial events, with thresholds and timing of interrupt generators programmable by the end user. The ultra low-power operational modes of LIS331HH sensors allow advanced power saving and smart sleep to wake-up functions. STMicrolectronics' STEVAL-MKI092VI Series adapter board is designed to facilitate the evaluation of MEMS devices in the LIS331HH product family. This adapter board offers an effective solution for fast system prototyping and device evaluation directly within the user's own application, featuring a complete LIS331HH pinout for a standard DIL 24 socket. The STEVAL-MKI092VI adapter board is fully compatible with all other available adapter boards.
STMicroelectronics STP1612PW05 16-Channel LED Driver
The STMicroelectronics STP1612PW05 is the first intelligent PWM-embedded LED driver. The STMicroelectronics STP1612PW05 takes advantage of Scrambled-PWM leading edge technology to effectively increase the refresh rate and provide 12 or 16-bit color depths for better image process and color enrichment in video display panels. The STMicroelectronics STP1612PW05 is a 16-channel PWM embedded constant current sink LED driver with output ranging from 3mA to 60mA. This LED driver features open and short LED failure detection and programmable progressive output delay to minimize inrush current. The high clock frequency of 30MHz makes the device suitable for high data rate transmission.
STMicroelectronics STM8L-Discovery Board
The STMicroelectronics STM8L-Discovery Board is based on the STM8L152C6T6 microcontroller (MCU) and is a quick-start evaluation board for STM8L ultra-low-power MCUs. The STM8L Discovery Board is the quickest way to discover the STM8L, to program and use the device, and to build and debug applications. This STMicroelectronics evaluation board includes the embedded debugger ST-LINK and an IDD consumption measurement feature that helps you to discover the ultra-low-power efficiency. Numerous applications are available to learn, reuse, and modify codes for a fast time to proof-of-concept or demonstration. The STM8L-Discovery is ideal for hobbyists, developers, students, and support teams.
STMicroelectronics STM32 Value Line Discovery Kit
The STMicroelectronics STM32 Value line Discovery Kit is a quick and inexpensive way to discover STM32 32-bit microcontrollers (MCUs). The STMicroelectronics STM32 Value Line Discovery Kit is based on the STM32 Value line and includes a quick-start evaluation board with ST-LINK debugger / programmer that is delivered with IDE from Keil, IAR, and Atollic. The debugger can debug Discovery kit applications or other target board applications. This low-cost STMicroelectronics evaluation kit will satisfy hobbyists, first-time developers, and students.
STMicroelectronics SPBT2532C2.AT Bluetooth® Modules
STMicroelectronics SPBT2532C2.AT Bluetooth® Blue Modules provide a micro-sized, standalone solution for users requiring a simple wireless link. SPBT2532C2.AT Blue Modules offer the most advanced Bluetooth technology, a highly reliable and affordable platform and a10x13mm footprint. These STMicroelectronics devices feature an on-board STM32 microprocessor, memories (Flash, RAM), an EDR Bluetooth radio transceiver, and Bluetooth v2.1 compliance. STMicroelectronics SPBT2532C2.AT modules offer much faster data throughput and more serial interface flexibility and options. SPBT2532C2.AT Blue Modules are ideal for use in a variety of applications, including MP3 wireless streaming, sensor monitoring, patient monitoring, diagnostic and security, and data acquisition equipment.
STMicroelectronics STM32 Value Line MCUs
The STMicroelectronics STM32 Value Line (STM32F100xx) Microcontrollers
(MCUs) bring the advantages of the STM32 32-bit advanced
industry-standard core into cost-effective applications typically served
by 16-bit MCUs. STMicroelectronics STM32F100xx MCUs
combine a 24MHz ARM® Cortex™-M3 processor core with peripheral features
optimized for typical 16-bit applications, such as home-entertainment
products, appliances, and industrial equipment. STM32 Value Line MCUs
are pin-to-pin compatible with the STM32 portfolio and bring new
features such as 16-bit timers and CEC function to expand the range of
applications addressed in the consumer, appliance, and industrial
segments. STMicroelectronics STM32 Value Line MCUs are suitable
for use in application control and user interface, medical and handheld
equipment, PC peripherals, alarm systems, and more.
STMicroelectronics STM8L101xx / STM8L15xxx Ultra-Low Power MCUs -- EXPANSION
STMicroelectronics STM8L Ultra-Low Power 8-bit Microcontrollers (MCUs) feature reduced system cost, low power consumption / advanced features, short development cycles, and product longevity. The STMicroelectronics STM8L101xx MCU family features the enhanced STM8 CPU core, providing increased processing power (up to 16 MIPS at 16 MHz) while maintaining the advantages of a CISC architecture with improved code density, a 24-bit linear addressing space, and an optimized architecture for low power operations. All STM8L101x MCUs feature low power low-voltage single-supply program Flash memory. The 8-Kbyte devices embed data EEPROM. The STMicroelectronics STM8L151xx and STM8L152xx MCU families are pin-to-pin compatible with STM8L101xx devices. The STM8L151xx and STM8L152xx MCUs feature a power supply range from 1.8 to 3.6 V down to 1.65 V at power down, architecture optimized to reach ultralow consumption both in low power modes and Run mode, fast startup strategy from low power modes, flexible system clock, and ultrasafe reset.
STMicroelectronics M24LRx Dual Access Protocol RF EEPROM
The STMicroelectronics M24LR64-R Dual Access Protocol RF EEPROM family of memories provides the flexibility to remotely program or update electronic products anytime during their lifetime and anywhere in the supply chain. The EEPROM memory bank of the STMicroelectronics M24LR64-R can be accessed either by a standard I²C interface or by an ISO 15693 RF interface. The ISO 15693 RF interface is based on a passive RFID technology that does not require a battery or power to operate but instead gets the energy and data stream from the RF reader. This STMicroelectronics Dual Access Protocol EEPROM family is based on two industry-standard interfaces and features a unique and flexible data protection scheme that protects some or all of the information contained in the memory. The M24LR64-R family is optimized for use in a variety of applications, including medical equipment, industrial equipment, factory and building automation, computers / peripherals, and consumer electronics.
STMicroelectronics has expanded the M24LR Series of Dual Access Protocol RF EEPROMs. View the new M24LR16E Dual Access Protocol RF EEPROMs.
STMicroelectronics NK SuperMESH™ High Voltage MOSFETs
STMicroelectronics NK Zener-protected SuperMESH™ power MOSFETs represent an extreme optimization of the standard strip-based PowerMESH™ layout. STMicroelectronics NK SuperMESH MOSFETs push on-resistance significantly down while also ensuring a very good dv/dt capability for the most demanding applications. NK SuperMESH devices are gate charge minimized and 100% avalanche tested while also offering ESD improved capability and a new high voltage benchmark. These STMicroelectronics MOSFETs are designed for use in switching applications.
STMicroelectronics STM8L Ultra Low-Power Microcontrollers
The STMicroelectronics STM8L microcontroller (MCU) uses a new proprietary ultra-low leakage process and optimized architecture to provide high performance and ultra-low power consumption. The STMicroelectronics STM8L MCU is based on the 8-bit STM8 core and is optimal for many applications with special care on power savings. The STM8L embeds up to 4 different ultra low-power modes to offer users a high level of flexibility. This STMicroelectronics 8-bit MCU offers a high level of integration and a small footprint.