Arduino Ethernet Shields
Arduino Ethernet Shields connect your Arduino to the internet in mere minutes. Just plug this module onto your Arduino board, connect it to your network with an RJ45 cable (not included) and follow a few simple instructions to start controlling your world through the Internet. Arduino Ethernet Shields allow an Arduino board to connect to the internet. These shields are based on the Wiznet W5100 ethernet chip, which provides a network (IP) stack capable of both TCP and UDP. These shields support up to four simultaneous socket connections. Use the Ethernet library to write sketches that connect to the Internet using the shield. The ethernet shields connect to an Arduino board using long wire-wrap headers that extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.
Features
- Requires an Arduino board (not included)
- Operating voltage 5V (supplied from the Arduino Board)
- Ethernet Controller: W5100 with internal 16K buffer
- Connection speed: 10/100Mb
- Connection with Arduino on SPI port
- Current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable:
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Input voltage range 36V to 57V
- Overload and short-circuit protection
- 9V Output
- High efficiency DC/DC converter: typ 75% @ 50% load
- 1500V isolation (input to output)
|
|
|
|
Arduino A000064/65 Wireless Proto Shields
Arduino A000064/65 Wireless Proto Shields allow an Arduino board to easily connect with an RF Module, enabling wireless communication using external wireless modules. They are based on the Xbee® ZigBee® RF modules from Digi, but can use any Wireless module with the same footprint as XBee modules. Proto shield-connected modules can be used as serial/USB replacements or they can be put into command mode and configured for a variety of broadcast and mesh networking options. The shields break out each Xbee RF module pin to a through-hole solder pad for easy access.
The A000064 comes without SD slot, while the A000065 does include an on-board SD card slot. Both shields include a switch allowing for control via USB or the microcontroller.
Features
- Requires an Arduino board (not included)
- Operating voltage: 5V (supplied from the Arduino Board)
- Supports micro SD cards (A000065)
- Socket for wireless expansion modules
|
Arduino A000058 WiFi Shield
Arduino A000058 WiFi Shield connects your Arduino to the internet wirelessly. Connect it to your wireless network by following a few simple instructions to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits.
Features
- Requires an Arduino board (not included)
- Operating voltage 5V (supplied from the Arduino Board)
- Connection via: 802.11b/g networks
- Encryption types: WEP and WPA2 Persoanl
- Connection with Arduino on SPI port
- On-board micro SD slot
- ICSP headers
- FTDI connection for serial debugging of WiFi shield
- Micro-USB for updating WiFi shield firmware
|
|
Arduino A000043 GSM Shield
Arduino A000043 GSM Shields connect your Arduino to the internet using the GPRS wireless network. Arduino A000043 GSM Shields plug into your Arduino board, supply a SIM card from an operator offering GPRS coverage and follow a few simple instructions to start controlling your world through the internet. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
|
Features
- Requires an Arduino board (not included)
- Operating Voltage 5V (supplied from the Arduino Board
- Quad-band GSM/GPRS Modem: GSM850MHz, GSM900MHz, DCS1800MHz, and PCS1900MHz
- Supports TCP/UDP and HTTP protocols through GPRS connection
- GPRS data downlink/uplink transfer speed max is 85.6kbps
- Requires SIM card provided by a network operator
|
Arduino A000079 Motor Shield
Arduino A000079 Motor Shield is based on the L298, which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC, and stepping motors. This shield lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board. This shield has two separate channels, called A and B, that each use 4 of the Arduino pins to choose the rotation direction, vary the speed, fast brake, or sense the current that is flowing through the motor. In total, there are 8 pins in use on this shield. You can use each channel separately to drive two DC motors or combine them to drive one bipolar stepper motor.
Features
- Operating Voltage: 5V to 12V
- Motor controller: L298P, Drives 2 DC motors or 1 stepper motor
- Max current: 2A per channel or 4A max (with external power supply)
- Current sensing: 1.65V/A
- Free running stop and brake function
|
|
Arduino A000077 Proto Shield
Arduino A000077 Prototyping Shield makes it easy for you to design custom circuits for your next Arduino project. You can solder parts to the prototyping area to create your project, or use it with a small solderless breadboard (not included) to quickly test circuit ideas without having to solder. It's got extra connections for all of the Arduino I/O pins, and it's got space to mount through-hole and surface mount integrated circuits if you need to as well. It's a convenient way to make your custom circuit and Arduino into a single module.
Features
- Requires an Arduino board (not included)
- Arduino 1.0 pinout
- Large 0.1" prototyping area
- Reset button
- 14 pin SMD footprint (50 mils pitch)
- 20 pin Trough Hole footprint (100 mils pitch)
- SPI header
- Long and easy-to-solder ground / 5V rails
|
Arduino A000080 MEGA Proto PCB Rev3
MEGA Proto PCB Rev3 makes it easy for users to design custom circuits for their next Arduino MEGA project. Designers can solder parts to the prototyping area to create their project or use it with a small solderless breadboard (not included) to quickly test circuit ideas without having to solder. It includes extra connections for all of the Arduino I/O pins and has space to mount through-hole and surface mount ICs. It's a convenient way to make a custom circuit and Arduino into a single module.
Arduino A000081 MEGA Proto Shield Kit Rev3
Arduino A000081 MEGA Proto Shield Kit Rev3 allows designers to move their projects from the breadboard to an Arduino MEGA-compatible PCB. Additional components included: 1 Straight single line pinhead connectors 40x1 1 Straight single line pinhead connectors 18x2 2 PCB Pushbutton 1 red led 1 yellow led 1 green led 5 10K Ohm Resistors 1/4W 5 220 Ohm Resistors 1/4W 5 1K Ohm Resistors 1/4W. On the Proto Shield PCB you’ll find: ICSP header 2X SOIC prototyping area up to 14-pin SOIC chip, narrow medium or wide package and long and easy-to-solder ground / 5V rails.
Arduino A000082 Prototyping Shield PCB
Arduino Prototyping Shield PCB makes it easy for users to design custom circuits for their next Arduino project. Designers can solder parts to the prototyping area to create their project or use it with a small solderless breadboard (not included) to quickly test circuit ideas without having to solder. It includes extra connections for all of the Arduino I/O pins and has space to mount through-hole and surface mount ICs. It's a convenient way to make a custom circuit and Arduino into a single module.
Summary
-
Requires an Arduino board (not included)
- Arduino 1.0 pinout
- Large 0.1 prototyping area
- Reset button
- 14 pin SMD footprint (50 mils pitch)
- 20 pin Trough Hole footprint (100 mils pitch)
- SPI header
- Long and easy-to-solder ground / 5V rails
|
Arduino A000083 Prototyping Shield Kit
Arduino A000083 Prototyping Shield Kit makes it easy for users to design custom circuits for theirr next Arduino project. Designers can solder parts to the prototyping area to create their project or use it with a small solderless breadboard (not included) to quickly test circuit ideas without having to solder. It has extra connections for all of the Arduino I/O pins and has space to mount through-hole and surface mount ICs. It's a convenient way to make a custom circuit and Arduino into a single module. Proto Shield Kit allows users to move their projects from a breadboard to an Arduino-compatible PCB. Included are a number of common components.
Component List
-
1 Straight single line pinhead connectors 40x1
- 1 Straight single line pinhead connectors 3x2
- 2 PCB Pushbutton
- 1 red led
- 1 yellow led
- 1 green led
- 5 10K Ohm Resistors 1/4W
- 5 220 Ohm Resistors 1/4W
- 5 1K Ohm Resistors 1/4W
|
|
|
