Contact Mouser (USA)  (800) 346-6873     |     Feedback        
View Cart     |     Change Location  USD
United States United States

Please confirm your currency selection:

US Dollars
Home » NEWEST Products » New by Manufacturer » Swissbit » Industrial SD Memory Cards - Swissbit
NEWEST Products
Swissbit Industrial SD Memory Cards

Swissbit Industrial SD Memory Cards

Swissbit’s Industrial SD Memory Cards are specifically designed, manufactured and tested to withstand extreme environmental conditions. The use of SLC (Single Level Cell) Flash combined with an optimized flash controller provides a number of enhanced product features such as built-in error correction, sophisticated wear leveling and bad block management algorithms, power loss protection and power saving modes. Special attention is dedicated to the mechanical stability and enhanced ESD protection. A high reliability housing with special connector support provides resistance against bending and torque. Furthermore, the gold plated SD Memory Card connectors will last a minimum of 10,000 insertions.

Swissbit's S-200/220 Industrial SD Memory Cards are a small form factor non-volatile memory card which provides high capacity data storage. It is designed to capture, retain and transport data, audio and images, facilitating the transfer of all types of digital information between a large variety of digital systems. The Card operates in two basic modes, SD card mode and SPI mode. The SD Memory Cards supports SD High Speed mode with up to 50MHz clock frequency. The Card has an internal intelligent controller which manages interface protocols, data storage and retrieval as well as hardware RS-code Error Correction Code (ECC), defect handling, diagnostics and clock control.


Additional Resources
S-200 Datasheet
S-200 Factsheet
S-220 Datasheet
S-220 Factsheet
Security and Monitoring Features
Features
  • Custom-designed, highly-integrated memory controller
    • Fully compliant with SD Memory Card specification 2.0
    • Four integrated 4KByte Sector Buffers for fast data transfer
    • SPI Mode support
  • Standard SD Memory Card form factor
    • 32.0mm x 24.0mm x 2.1mm
    • Write Protect slider
  • 2.7…3.6V normal operating voltage
  • 2.0…3.6V basic communication (CMD0, 15, 55 ACMD41) voltage
  • Low-power CMOS technology
  • Wear Leveling: equal wear leveling of static and dynamic data, assures that dynamic data as well as static data is balanced evenly across the memory with the maximum write endurance of the device guaranteed
  • Patented power-off reliability
  • High reliability
    • Best available SLC NAND Flash technology
    • Designed for embedded market
    • MTBF: > 3,000,000 hours (S-200), 4,000,000 (S-220)
    • Number of insertions: >10,000
    • Extended Temperature range -25° up to 85°C
    • Optional industrial Temperature range available -40° up to 85°C

  • Hot swappable
  • High performance
    • SD burst up to 25MB/s
    • SD Low speed 0…25MHz clock rate
    • SD High speed 25…50MHz clock rate
    • Flash burst up to 40MB/s
  • Available densities
    • Up to 8GBytes
  • Controlled BOM
  • Life Time Monitoring SD/SPI with standard or vendor commands
 

Swissbit's S-200u/300u Industrial MICRO SD Memory Cards are a small form factor non-volatile memory card which provides high capacity data storage. Its aim is to capture, retain and transport data, audio and images, facilitating the transfer of all types of digital information between a large variety of digital systems. The Card operates in two basic modes, SD card mode and SPI mode. The MICRO SD Memory Cards supports SD High Speed mode with up to 50MHz clock frequency. The Card has an internal intelligent controller which manages interface protocols, data storage and retrieval as well as hardware RS-code Error Correction Code (ECC), defect handling, diagnostics and clock control.


Additional Resources
S-200u Datasheet
S-300u Datasheet
S-300u Factsheet
Security and Monitoring Features
Swissbit S-200u/S-300uIndustrial MICRO SD Memory Cards
Order Swissbit S-200u/300u Industrial MICRO SD Memory Cards View Product List
Features
  • Highly-integrated memory controller
    • Fully compliant with SD Memory Card specification 2.0 and Micro SD Memory Card
      specification 2.0 (S-200u) and SD Memory Card specification SD1.01, SD1.1, SD2.0
      and SD3.01 and MICRO SD Memory Card Addendum 4.00 (S-300u)
  • Standard MICRO SD Memory Card form factor
    • 15.0mm x 11.0mm x 0.7mm
  • Operating Voltage: 2.7-3.6V
  • Low-power CMOS technology
  • Wear Leveling: equal wear leveling of static and dynamic data, assures that dynamic data as well as static data is balanced evenly across the memory with the maximum write endurance of the device guaranteed
  • High reliability
    • MTBF: > 3,000,000 hours
    • Number of insertions: >10,000
    • Extended Temperature range: -25° up to 85°C
    • Industrial Temperature range: -40° up to 85°C

  • Hot swappable
  • High performance
    • SD burst up to 25MB/s
    • SD Low speed 0…25MHz clock rate
    • SD High speed 25…50MHz clock rate
    • Flash burst up to 40MB/s
  • Available densities
    • Up to 8GBytes
     
  • Swissbit