Murata Power Solutions UEE Series DC-DC Converters
Murata Power Solutions UEE Series DC-DC Converters are fully isolated eighth brick modules, available with pins (on quarter brick pinout) in a DOSA compatible package, or surface mount option. The UEE DC-DC Converters from Murata feature fixed output voltage and current rating up to 30 Amps. With a wide operating range of up to +85ºC, on-board sensor technology shuts down the unit if thermal limits are reached, then automatically resets when the fault is removed. On/Off control input allows phased startup/shutdown in multi-voltage applications. The UEE Series is protected against input undervoltage, output overcurrent, and short circuit.
Murata Power Solutions MEV1 1W DC/DC Converter - EXPANSION
Murata Power Solutions MEV1 high performance series of 1W 3kVDC Isolated DC/DC Converters now includes dual output versions.
View entire MEV1 Series, including single output versions.
Murata Okami™ OKI -78SR Series DC/DC Converters - EXPANSION
The Murata Power Solutions Okami line is now available in the OKI -78SR Series, a horizontal mount version.
See the entire Murata Power Solutions Okami™ OKI-78SR Series.
The Murata Power Solutions OKI-78SR Series 1.5Amp DC/DC Converters are fixed output SIP converters fabricated on a 0.41" x 0.65" (10.4mm x 16.5mm) module. These non-isolated switching regulator (SR) DC/DC power converters are for embedded applications. The OKI-78SR
Series offers both tight regulation and high efficiency directly at the
power usage site and are a direct plug-in replacement for TO-220
package 78xx series linear regulators. Typically, no extra outside components are required. The Murata Power Solutions OKI-78SR Series 1.5Amp DC/DC Converters feature an ultra wide 7 - 36 VDC input range.
Datel / Murata OKI Series DC/DC Converters - EXPANSION
Murata Power Solutions has expanded the Datel / Murata OKI Series of point of load (PoL) DC/DC Converters to include the OKI-T/3-W32 Series, designed for +12 or +24 VCD industrial applications. This new series has a wide input voltage range of +9 to +32 VDC, allowing designers to use one part for both nominal input voltages. The Datel / Murata OKI-T/3-W32 DC/DC Converters are ideal for low voltage powering of FPGAs and microprocessors in higher voltage applications.
View the entire Datel / Murata OKI Series
Datel / Murata Power Solutions´ Okami™ OKI series of 3A output current, surface mount DC/DC Converters is an addition to the Okami family of non-isolated, DOSA compatible pin-out, point-of-load (PoL) DC/DC converters. The OKI-T/3-W40 series is ideal for 24V industrial applications. The 15W maximum output power OKI series has a wide input range of 16VDC to 40VDC and a programmable output voltage of 0.75VDC to 5.5VDC. The Datel / Murata OKI series features on/off control, over-temperature, over-current, and under-voltage lock out (UVLO) protection. The new Okami OKI-T/3-W40 series of PoL DC/DC Converters meet all standard UL/EN/IEC 60950-1 safety certifications and is compliant with RoHS-6 hazardous substance regulations.
Murata Power Solutions 2700/2700T Series SM Power Inductors
Murata Power Solutions designed the 2700 and 2700T Series SM Power Inductors for applications requiring low component height, such as handheld equipment and notebook computers. The 2700 Series offer a range of inductance values of 4.7 to 1000µH, a device dependent maximum DC current up to 1.6A, and DC resistance ranging from 0.1Ω to 14Ω. The 2700T Series provides inductance in the range of 1 to 330 µH, maximum current of 2.0A, and DC resistance of 80mΩ to 15Ω. The 2700/2700T Series SM Power Inductors from Murata Power Solutions has an operating temperature range of -40 to +125ºC.
Murata Power Solutions 8300 Series Toroidal SM Power Inductors
Murata Power Solutions' 8300 Series Toroidal SM Power Inductors are space-saving miniature low-profile devices measuring 7.8 x 5.20 x 1.8mm. They are ideal for handheld consumer devices with PCB footprint and height restrictions. EMI characteristics are excellent due to the toroidal core's ability to confine the magnetic flux to the core and the virtual elimination of stray fields. The 8300 Series Toroidal SM Power Inductors from Murata Power Solutions has a device dependent maximum DC current of 3.0 A, inductance from 0.42 to 100 µH, and DC resistance from 24mΩ to 1320mΩ. The operating temperature range is -40 to +86ºC.
Murata Power Solutions Flat Coil SM Power Inductors
The 3700, 3800, and 3900 Series from Murata Power Solutions are Flat Coil Surface Mount Power Inductors designed for high current, low loss applications. The power inductors provide a wide range of inductance values from 0.15 tp 10µH with DC ratings up to 19.5A. Extremely small sizes offer space savings, with the smallest part measuring just 14.5 x 11.5 x 5.8mm (0.571 x 0.453 x 0.228 inches). With DC resistance values ranging from 0.9 to 20.3mOhm, voltage drop is kept to an absolute minimum. Typical applications for the Murata Power Solutions Flat Coil SM Power Inductors include voltage regulator modules, notebook computers, plasma displays, and other dc-dc power conversion applications where a high transient response is needed. The operating temperature range of -40 to +130ºC make these inductors suitable for many environments.
UEI25 Series Isolated DC/DC Converters - EXPANSION
Murata Power Solutions now has Surface Mount Models of UEI25 Series of DC-DC Converters.
View the entire UEI25 Series.
Murata Power Solutions introduces the UEI25 Series of 25W output, 2:1 input range, 12V output, high-efficiency, isolated DC-DC converters. Featuring 25W output in one square inch of board area, Murata Power Solutions' UEI25 Series DC-DC converter offers efficient regulated DC power
for PCB mounting. The low-profile 0.96" x 1.1" x 0.32" converters
accept a 2:1 input voltage range of 36 to 75VDC, ideal for industrial
and telecom equipment applications. The output can be trimmed up or down
by 10% with an external trim resistor. The highly efficient design (up
to 87.5%) ensures minimal power loss allowing "no-fan" operation.
Both through-hole and SMD versions of the UEI25 Series are available.
Murata Power Solutions RBC Series DC-DC Converter
Murata Power Solutions RBC Series of DC-DC Converters are optimized for distributed power Regulated Intermediate Bus Architectures (RIBA). It offers regulated output in a quarter brick open frame package. The RBC Series from Murata is available with positive or negative polarity.
Murata Power Solutions ULS 30W DC-DC Converters - EXPANSION
Murata Power Solutions' sixteenth brick ULS Series is now available with 30W output. The ULS 30W Series is ideal for embedded applications.
View the entire ULS Series.
The Murata Power Solutions ULS Series Isolated DC-DC Converters
have progressed down to a sixteenth-brick width (0.9"), while still
retaining a 66 Watt output and a full 2250 Volt DC isolation. The
PC-board mount converter family accepts 36 -75 Volts DC inputs and
delivers fixed outputs regulated to within ±0.2%. The Murata Power Solutions ULS Series Isolated DC-DC Converters
are ideal for high current applications such as datacom, telecom, cell
phone towers, data centers, server farms, and network repeaters. Learn more
Murata Power Solutions UWE Series Eighth-Brick DC/DC Converters
Murata Power Solutions has expanded their UWE Series Eighth-Brick DC/DC Converters. The offering now includes models with 48V input.
View the entire UWE Series.
The Murata Power Solutions UWE Series Eighth-Brick DC/DC Converters are high-current isolated power modules for use in high-density system boards. Wide input (9-36VDC or 18-75VDC) makes the UWE Series ideal for battery-powered, telecom, or portable applications. The UWE DC/DC Converters measure
only 0.9" x 2.3" x 0.38" and can plug directly into quarter-brick
pinouts. They possess several standard fixed-output voltages from 3.3VDC
to 24VDC to assure compatibility in embedded equipment, CPU cards, and
instrument subsystems.
Murata Power Solutions ACM20 Series Panel Meters EXPANSION
Murata Power Solutions has expanded its ACM20 Series of Four-Function AC Power Meters. The two new models are the industry's first digital AC power panel meters with measurement resolution of 0.001A and 0.1W, ideal for testing low-current AC-powered products.
Murata Power Solutions' ACM20 Series of Four-Function AC Power Meters display the most critical measurements in mains-powered equipment: voltage, amperage, active power (watts), and power factor. A front panel selector-switch provides two modes of operation: a fixed reading or continuous auto-cycling. All Murata Power Solutions ACM20 AC Power Meters
include built-in current transformers - no other user-supplied
components are required. The miniature units are packaged in a
one-piece, vibration resistant, polycarbonate housing that can be
installed in vertical "0U" and "1U" rack spaces. Perfect for UPS power
sources, power strips, laboratory instrumentation, alternate energy
applications, and any other products that require precise monitoring of AC power.
View the entire series of Murata's ACM20 Power Meters.
Murata Power Solutions DA100J Series Transformers for Audio Digital Transmission
Murata Power Solutions DA100J Series Transformers for Audio Digital Transmission are compatible with leading chip sets. They are compliant with AES/EBU standards for digital audio interface. These surface mount transformers are capable of operating over the audio data rate frequency range and provide isolation from 50 - 60Hz noise. The DA100J Series from Murata Power Solutions were designed to improve the balance of transmitter and receiver circuitry in hi-fi equipment and video games. They are also suitable for other applications requiring high-performance digital audio transmission.
Murata Power Solutions 786J Series General Purpose SMT Transformers
Murata Power Solutions 786J Series General Purpose Pulse Transformers feature J-STD-020D reflow and toroidal construction. These surface mount General Purpose Pulse Transformers can be used in line coupling, matching, or isolating applications. They can also be used in small isolated power supplies as well as common-mode chokes in filtering applications. This comprehensive range of transformers from Murata Power Solutions is available in four winding configurations.
Murata Power Solutions 78253J Series MAX253 Compatible Converter SMT Transformers
Murata Power Solutions 78253J Series MAX253 Compatible Converter SM Transformers were specifically designed for use with the MAX253 chip set to provide isolated power supplies. The 78253J Series MAX253 Compatible Converter SM Transformers feature J-STD-020D reflow, toroidal construction, and isolation to 4kVDC. They are available in 3.3V and 5V versions. Murata Power Solutions has provided a center tapped secondary winding which allows for full bridge, half bridge, or voltage doubling.
Murata Power Solutions MAX250/MAX251 Compatible Converter SMT Transformers
The 78250J Series Converter Transformers from Murata Power Solutions were specifically designed for use with Maxim MAX250/MAX251 chip sets to provide isolated RS232 interfaces. Murata Power Solutions has ensured consistent performance with carefully controlled ratio turns. The 78250J Series Converter Transformers feature J-STD-020D reflow and isolation to 4kVrms. Toroidal construction minimizes EMI.
Murata Power Solutions 2200RM Series Surface Mount Inductor
Murata Power Solutions' 2200RM Inductor Series is a surface mount alternative to the general-purpose, PCB-mountable 2200R Series ideal for low to medium current applications. Like the 2200R Series, Murata's 2200RM Series bobbin wound surface mount inductor has a miniature size, low DC resistance, and small footprint that makes it ideal for high density applications where a chip inductor is not compatible with the power requirement.
Murata HPQ-8.3/22-D48 Series Isolated 22-Amp Quarter Brick DC/DC Converter
Murata Power Solutions' HPQ-8.3/22-D48 Series Isolated 22-Amp Quarter Brick DC/DC Converter Series provides fixed 8.3 Vdc output at 183 Watts for printed circuit board mounting. Murata's HPQ-8.3/22-D48 Series isolated converter also offers high output current (up to 22 Amps) in an industry-standard "quarter brick" open frame package (2.3" x 1.45" x 0.4") that doesn't require a heat sink for most applications. In addition, this high efficiency (92.5%) DC/DC converter is certified to UL safety standards (pending) and RFI/EMI conducted/radiated emission compliance to EN55022, CISPR22 with external filter.