Monolithic Power Systems (MPS) is a high performance analog semiconductor company headquartered in San Jose, California. Monolithic Power Systems (MPS) has three core strengths; deep system-level and applications knowledge, strong analog design expertise, and an innovative proprietary process technology. These combined advantages enable MPS to deliver highly integrated monolithic products that offer energy efficient, cost-effective solutions.
MPS MP8760 voltage regulator is a fully-integrated,
highfrequency, synchronous, rectified, step-down, switch-mode converter.
It offers a very compact solution to achieve a 6A output current over a
wide input-supply range with excellent load and line regulation. The
MP8760 operates at high efficiency over a wide output-current load
range. The MP8760 uses Constant-On-Time (COT) control mode to provide
fast transient response and ease loop stabilization. An external
resistor programs the operating frequency from 200kHz to 1MHz. The
frequency stays nearly constant as the input supply varies with the
feed-forward compensation. The default under voltage lockout threshold
is 4.1V, but a resistor network on the enable pin can increase this
threshold. The soft start pin controls the output voltage startup ramp.
An open drain power good signal indicates that the output is within
nominal voltage range. It has full integrated protection features that
include over-current protection, over-voltage protection and thermal
shutdown. The MPS MP8760 voltage regulator is available in a 3mm×4mm QFN
package, and requires a minimal number of readily-available components.
MPS MP3426 voltage regulators are current-mode step up converters with a 6A, 90mOhm internal switch that provides a highly efficient regulator with a fast response. The MP3426 features a programmable frequency of up to 2MHz that allows for easy filtering and reduces noise. An external compensation pin gives the user flexibility in setting loop dynamics, and uses small, low-ESR, ceramic output capacitors. Soft-start results in a small inrush current and can be programmed with an external capacitor. The MP3426 operates from an input voltage as low as 3.2V and can generate up to a 35V output. The MP3426’s features include under-voltage lockout, current limiting, and thermal overload protection. MPS MP3426 voltage regulators are available in a low-profile 14-pin 3mm×4mm QFN package with an exposed pad.
MPS MPQ4559 voltage regulators are high frequency step-down switching regulators with integrated internal high-side high voltage power MOSFET. It provides 1.5A output with current mode control for fast loop response and easy compensation. The wide 3.8V to 55V input range accommodates a variety of step-down applications, including those in automotive input environment. A 12µA shutdown mode supply current allows use in battery-powered applications. High power conversion efficiency over a wide load range is achieved by scaling down the switching frequency at light load condition to reduce the switching and gate driving losses. The frequency foldback helps prevent inductor current runaway during startup and thermal shutdown provides reliable, fault tolerant operation. By switching at 2MHz, the MPQ4559 is able to prevent EMI (Electromagnetic Interference) noise problems, such as those found in AM radio and ADSL applications. MPS MPQ4559 voltage regulators are available in small 3mm x 3mm QFN10 and SOIC8 with exposed pad packages.
MPS MP22xx step-down converters are high-frequency, synchronous, rectified, switch-mode converters with built-in power MOSFETs. MP22xx converters offer a compact solution to achieve a 2A/3A continuous output current with excellent load and line regulation over a wide input supply range. The MP22xx has synchronous mode operation for higher efficiency over the output current load range. Current-mode operation provides fast transient response and eases loop stabilization. Full protection features include over-current protection and thermal shut down. MPS MP22xx step-down converters require a minimal number of readily-available standard external components, and are available in a space-saving 8-pin TSOT23 package.
MPS MP4030 LED lighting drivers are TRIAC dimmable, primary-side-control offline LED lighting controllers which can achieve high power factors and accurate output LED currents for isolate lighting applications. Proprietary real current control method can control LED current accurately from the primary side information. MP4030 drivers can significantly simplify LED lighting system design by eliminating the secondary side feedback components and the optocoupler. MPS MP4030 LED lighting drivers implement power factor correction function and work in boundary conduction mode for reducing MOSFET switching losses. The MP4030 internally integrated a charging circuit at VCC for fast start-up without perceptible delay. The TRIAC-based dimming range is mostly enlarged with proprietary dimming control. The multi-protection function of MP4030 can greatly enhance the system reliability and safety. The MP4030 features auto-restart with all fault protections, including over-voltage protection, short-circuit protection, programmable primary side over current protection, VCC UVLO and over-temperature protection.
MPS MP5000 load switches are protection devices designed to protect circuitry on the output (source) from transients on the input (VCC). MP5000 also protect VCC from undesired shorts and transients coming from the source. At start up, inrush current is limited by limiting the slew rate at the source. The slew rate is controlled by a small capacitor at the dv/dt pin. The dv/dt pin has an internal circuit that allows the customer to float this pin (no connect) and still receives a 1.5ms ramp time at the source. The max load at the output (source) is current limited. This is accomplished by utilizing a sense FET topology. The magnitude of the current limit is controlled by an external resistor from the I-Limit pin to the Source pin. An internal charge pump drives the gate of the power device, allowing a very low on-resistance DMOS power FET of just 0.07Ohms. MPS MP5000 load switches are protected from the VCC input being too low or too high. Under Voltage Lockout (UVLO) assures that VCC is above the minimum operating threshold, before the power device is turned on. If VCC goes above the high output threshold, the source voltage will be limited.
MPS MPM3810 voltage regulators are modules with monolithic step-down switch mode converters with built-in internal power MOSFETs and inductors. MPM3810 is designed to simplify power system design and provide ease of use. The DC-DC module has a small surface-mount 3mm x 2.5mm x 0.9mm QFN package. It achieves 1.2A Peak output current from a 2.5V to 6V input voltage with excellent load and line regulation. The output voltage can be regulated as low as 0.6V. The Constant-On-time control scheme provides fast transient response and eases loop stabilization. Fault condition protection includes cycle-by-cycle current limiting and thermal shutdown. The MPM3810 is ideal for a wide range of applications including high performance DSPs, FPGAs, PDAs, portable instruments and storage.
MPS MP157 EasyPower voltage converters are primary-side regulators which provide accurate and constant voltage (CV) regulation without the Opto-coupler. MP157 supports Buck, Buck-Boost, Boost and Flyback topologies. These regulators are integrated with 500V MOSFET for simple structure and low cost making MP157 ideal for off-line low power applications including home appliance, standby power, and industrial control. When the load decreases, the peak current and the switching frequency decrease with the load. As a result, MP157 still offers excellent efficiency performance at light load, and better average efficiency is achieved. MPS MP157 EasyPower voltage converters feature various protections like Thermal Shutdown (TSD), VCC under Voltage Lockout (UVLO), Over Load Protection (OLP), Short Circuit Protection (SCP), Open Loop Protection. MP157 is available in the TSOT23-5 and SOIC8 packages.
MPS MP6400 Supervisory Circuit is a microprocessor that monitors and provides reset function for system voltages from 0.4V. Two versions are available: reset voltage is either factory-set or user-adjustable. MP6400 features a very low quiescent current of 1.6µA, making it ideally suited for battery-powered applications.
Monolithic Power Systems HFC0300 Variable Off Time Controller uses a fixed-peak-current technique to decrease its frequency as the load lightens. As a result, the HFC0300 Variable Off Time Controller offers excellent efficiency at light-load while optimizing the efficiency under other load conditions. When the frequency decreases to threshold, the peak current decreases to prevent mechanical resonance in the transformer. MPS' HFC0300 Variable Off Time Controller enters burst mode when the output power falls below a given level. Features for the Monolithic Power Systems HFC0300 Variable Off Time Controller includes various protections such as thermal shutdown, VCC under-voltage lockout, overload protection, short-circuit protection, and over-voltage protection.
Monolithic Power Systems MP4021 Primary Side Control Offline LED Controller
is an off-line LED lighting controller that achieves high power factor
and accurate LED current for single-power stage, isolated lighting
applications. The proprietary real current control method of the MP4021 Primary Side Offline LED Controller
accurately controls the LED current from the primary side, and
therefore significantly simplifies the LED lighting system design by
eliminating the secondary side feedback components and the optocoupler.
The Monolithic Power Systems MP4021 Primary Side Control Offline LED Controller
integrates power factor correction and works in boundary conduction
mode to reduce the MOSFET switching losses. Applications include solid state, industrial, commercial and residential lighting.
Monolithic Power Systems MP8620 Fully Integrated Synchronous Step-Down Converter is a fully integrated step-down converter with internal power MOSFETs. The MP8620 Fully Integrated Synchronous Step-Down Converter achieves 25A continuous output current over a wide input supply range with excellent load and line regulation. Monolithic Power Systems' MP8620 can be configured and optimized as a single phase or a multi-phase solution to support high current (50A-100A) applications. This provides the flexibility and at the same time meets the efficiency requirement with less components. MP8620 operates reliably even with low duty cycle and noisy environment. Fault condition protection include cycle-by-cycle current limit, thermal shutdown, output short-circuit, output under voltage and output over voltage protection. The Monolithic Power Systems MP8620 is suitable for a wide range of space-constraint applications, including point of load regulation for FPGAs, ASICs, DDR memory power, and power systems for networking and data centers.
Monolithic Power Systems MP2825x Synchronous Step-Down Converter is a fully-integrated, high-efficiency, synchronous, step-down, switch mode converter. The MP2825x High Efficiency, Fast Transient, Synchronous Step-Down Converter offers a very compact solution that can achieve up to 4A
continuous output current over a wide input supply range with excellent
load and line regulation, and can operate at high efficiency over a
wide output-current load range. Full protection features of the Monolithic Power Systems MP2825x High Efficiency, Fast Transient, Synchronous Step-Down Converter includes SCP, OCP, OVP, UVP and, thermal shut down.
Monolithic Power Systems MP2130 Synchronous Switcher is a monolithic step-down switch mode converter with built-in internal power MOSFETs. The MP2130 High Light-Load Efficiency, Low-Voltage, Synchronous Switcher achieves 3.5A continuous output current from a 2.7V to 6V input voltage with excellent load and line regulation. Monolithic Power Systems' MP2130 is ideal for powering portable equipment that runs from a single cell Lithium-Ion (Li+) Battery. MP2130 High Light-Load Efficiency, Low Voltage, Synchronous Switcher is ideal for a wide range of applications including PDAs, portable instruments, DVD drives, small handheld and battery-powered devices.