Swissbit, a global leader in the design, development, and manufacture of DRAM and Flash memory products, supplies high quality memory solutions to the Industrial, Embedded, Communications & Networking, Military & Aerospace, Transportation, Casino Gaming, and Medical Equipment markets.
Swissbit U-110 USB Flash Modules provide non-volatile, solid-state storage in a compact design, making it perfectly suited for embedded applications. The standard USB 2.0 interface provides designers with a true plug-n-play storage device, allowing for short design cycles and fast time to market. Swissbit use high end USB 2.0 flash memory controller in the Module, providing high data reliability and endurance. The built-in BCH-ECC engine can detect up to 9-bit errors and correct up to 8-bit errors, while sophisticated wear leveling algorithms guarantee up to 2,000,000 Write Cycles. The internal USB Flash Drive Module has an internal 9(10) pin USB connector. High performance, high reliability and low cost per megabyte make the internal USB Flash Drive Module the product of choice in embedded applications, such as Gaming, POS Workstations, Networking Equipment and Industrial PCs.
Swissbit F-240 CFAST Card combines the CompactFlash™ (CF) form factor and the Serial ATA (SATA) interface. It can replace both HDDs and CF cards in applications requiring small form factors. The F-240 CFAST cards are designed for long life, and the ability to endure shock, vibration, extreme temperatures, high altitude, and rough environments. It operates with on a 3.3V source, and supports 3 SATA power management states: Active, Partial, and Slumber.
Swissbit's P-120 PATA 2.5" Solid-State Drive for low to medium density applications offers a drop-in replacements for traditional 2.5" hard disk drives (HDD). These SSD are offered as a Parallel ATA (PATA)/IDE drive designed for long-term industrial usage. It supports key requirements such as long data retention, no compromise power fail safety and long product life cycles. P-120 uses the most reliable SLC Flash in combination with rugged hardware design and approved firmware technologies in order to provide the best performance in quality, reliability and data integrity.
Swissbit DRAM memory modules are industry standard 200/204-pin 8-byte DDR2/DDR3 SDRAM small outline dual-in-line modules which are organized as x64 high speed CMOS memory arrays. The module uses internally configured octal-bank SDRAM devices. The DDR3 module uses double data rate architecture to achieve high-speed operation. These memory modules operate from a differential clock (CK and CK#). READ and WRITE accesses to the SDRAM modules are burst-oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. The burst length is either four or eight locations. An auto precharge function can be enabled to provide a self-timed row precharge that is initiated at the end of a burst access. Swissbit DRAM memory modules have a multibank architecture which allows a concurrent operation that is providing a high effective bandwidth. Swissbit uses internally developed application software to test 100% of all modules under real world conditions with diverse pattern and stress methods and to cover the complete memory array including ECC components by constantly adapting to the latest memory controller features. For industrial temperature grade modules the application tests are performed at -40°C and 85°C T AMBIENT.
Swissbit X-55 SATA SSDs are ideally suited for cost-sensitive
industrial applications with tough requirements such as broad
temperature ranges (-40°C and +85°C), transparent diagnostic functions,
and enhanced erase methods. The X-55 SSDs provide excellent cost per
gigabyte and offer high data reliability with Swissbit's industry
leading power fail protection feature, S.M.A.R.T. protocol, lifetime
monitoring tools and SDK/API, as well as the highly efficient BCH-ECC
(error correction code). Additionally, these SATA flash drives include
features such as NCQ, TRIM, ATA Security Set and Enhanced Secure Erase
via software, as well as hardware management. Internal temperature
sensors continuously monitor the system, allowing the implementation of
additional early warning systems. The SATA connector with latch
protection and reinforced component assembly makes the X-55 suitable for
applications that demand high vibration and shock resistance. Swissbit
X-55 SATA SSDs are available in various densities.
Swissbit's x-200s Industrial slimSATA Solid State Drives (SSD) are small form factor 54mm x 39mm x 4mm non-volatile memory drives which provide high capacity data storage. They have a standard combined connector with SATA and power/control part. The connector is in the plane of the connector as specified in the JEDEC MO-297 specification. The card works at a supply voltage of 5V with an optional 3.3V available. The drive with the SATA interface operates in Mode 2.0 (1.5 or 3.0 Gb/s burst). The drive has an internal intelligent controller which manages interface protocols, data storage and retrieval as well as hardware BCH-code Error Correction Code (ECC), defect handling, diagnostics and clock control. The wear leveling mechanism assures an equal usage of the Flash memory cells to extend the life time. The hardware BCH-code ECC allows to detect and correct 8 random bits per 528 Bytes. The drive has a voltage detector and a powerful power-loss management feature to prevent data corruption after power-down.
Swissbit’s Industrial SD Memory Cards are specifically designed, manufactured and tested to withstand extreme environmental conditions. The use of SLC (Single Level Cell) Flash combined with an optimized flash controller provides a number of enhanced product features such as built-in error correction, sophisticated wear leveling and bad block management algorithms, power loss protection and power saving modes. Special attention is dedicated to the mechanical stability and enhanced ESD protection. A high reliability housing with special connector support provides resistance against bending and torque. Furthermore, the gold plated SD Memory Card connectors will last a minimum of 10,000 insertions.
Swissbit's x-200m Industrial mSATA Solid State Drives (SSD) are small form factor 50.8mm x 29.85 mm x 3.3mm) non-volatile memory drives which provide high capacity data storage. The SSDs are designed after the JEDEC MO-300 full size standard. They have a standard combined connector with SATA and power/control part. The connector is mechanical identical with eeePC card connector, but has different pinout. The card works at a supply voltage of 3.3V. The drive with the SATA interface operates in Mode 2.0 (1.5 or 3.0 Gb/s burst). The drive has an internal intelligent controller which manages interface protocols, data storage and retrieval as well as hardware BCH-code Error Correction Code (ECC), defect handling, diagnostics and clock control. The wear leveling mechanism assures an equal usage of the Flash memory cells to extend the life time. The hardware BCH-code ECC allows to detect and correct 8 random bits per 528 Bytes. The drive has a voltage detector and a powerful power-loss management feature to prevent data corruption after power-down.
Swissbit X-200/500/55 Series Solid State Drives (SSD) are drop-in replacements for traditional 2.5“ hard disk drives (HDD). The X-200 Series SSDs are offered in both, Parallel ATA (PATA) and Serial ATA (SATA) interfaces. This line is designed for industrial usage and does not support dedicated optimization techniques commonly used in "Enterprise SSDs“. Critical factors like long data retention, no compromise power fail safety and long product lifecycles are key for industrial customers. The X-500 Series Industrial SATA II SSD 2.5” storage solutions are designed for demanding applications. The Swissbit X-55 SATA SSDs offer many similar features and industrial capabilities at a lower price point using EM-MLC Flash technology. The Solid State Drive is a rugged, high performance and extremely reliable storage solution. The data rate reaches up to 240MB/sec and an impressive 14,500 IOPS with 4 KB random accesses. The high end architecture utilizes up to 8 channels with the most reliable SLC NAND Flash (X-200/X-500) on the market.
Swissbit's Industrial CompactFlash™ Cards are small form factor, non-volatile memory cards which provide high capacity data storage. They are designed to capture, retain, and transport data, audio, and images, facilitating the transfer of all types of digital information between a large variety of digital systems. These cards operate in three basic modes: PC card ATA I/O mode, PC card ATA memory mode, and True IDE mode. The CompactFlash also supports Advanced Timing modes. Advanced Timing modes are ATA I/O modes that are 100ns or faster, and ATA Memory modes that are 100ns or 80ns. These CompactFlash cards conform to the PCMCIA Card Specification 2.1 when operating in the ATA I/O mode, and in the ATA Memory mode (Personal Computer Memory Card International Association standard, JEIDA in Japan), and to the ATA specification when operating in True IDE Mode. CompactFlash Cards can be used with passive adapters in a PC-Card Type II or Type III socket.