Innovation, performance, and excellence are the cultural pillars on which Analog Devices (ADI) has built one of the longest standing, highest growth companies within the technology sector. Acknowledged industry-wide as the world leader in data conversion and signal conditioning technology, Analog Devices serves over 60,000 customers, representing virtually all types of electronic equipment. Analog Devices is headquartered in Norwood, Massachusetts, with design and manufacturing facilities throughout the world. Analog Devices is included in the S&P 500 Index.
Analog Devices ADV7281-M/ADV7282-M video decoders are versatile one-chip, multiformat decoders that automatically detect standard analog baseband video signals compatible with worldwide NTSC, PAL, and SECAM standards in the form of composite, S-Video, and component video. The ADV7281-M/ADV7282-M converts the analog video signals into a YCrCb 4:2:2 video data stream that is compatible with the 8-bit ITU-R BT.656 interface standard. The ADV7281-M/ADV7282-M convert the analog video signals into an 8-bit YCrCb 4:2:2 video data stream that is output over a mobile industry processor interface (MIPI) CSI-2 interface. The analog video inputs of the ADV7281-M/ADV7282-M accept single-ended, pseudo differential, and fully differential signals. The ADV7282-M contains a deinterlacer (I2P con-verter) and short to battery detection capability with two STB diagnostic pins. The ADV7281-M/ADV7282-M provides six analog inputs, two STB diagnostic pins, and three general-purpose outputs. The ADV7281-M/ADV7282-M are programmed via a 2-wire, serial bidirectional port (I2C compatible) and are fabricated in a 1.8V CMOS process. The LFCSP package option makes these decoders ideal for space-constrained portable applications.
Analog Devices ADDI7013 CCD signal processor is a highly integrated, dual-channel, processor for high speed digital imaging applications. Each channel is specified at pixel rates of up to 75MHz and consists of a complete analog front end (AFE) with analog-to-digital conversion. The Precision Timing core allows adjustment of the correlated double sampler (CDS) and horizontal clocks with 210ps resolution at 75MHz operation. There are eight independent horizontal clock outputs with programmable drive strength to support a variety of CCD timing requirements. Each analog front end includes black level clamping, a CDS, a VGA, and a 75MSPS, 16-bit analog-to-digital converter (ADC). Operation is programmed using a 3-wire serial interface. Analog Devices ADDI7013 CCD signal processor is packaged in a space-saving, 6mm × 6mm, CSP_BGA and is specified over an operating temperature range of -40°C to +85°C.
Analog Devices ADuM144x Quad-Channel Digital Isolators are micropower devices based on iCoupler® technology. ADI ADuM144x isolators combine high speed, CMOS, and monolithic air core transformer technologies to provide outstanding performance characteristics compared to optocoupler devices. These ADI digital isolators also offer the lowest power of any isolation device on the market. The ENX signals can be used to disable the internal refresh, which lowers the total quiescent current to less than 1µA. These devices free almost 70% of board space but can still withstand high isolation voltages and meet regulatory requirements. ADuM144x isolators operate with supplies as low as 2.25V. This device family also provides low, pulse width distortion <8ns. These devices also have an input glitch filter to protect against extraneous noise disturbances.
Analog Devices ADMP621 Wide Dynamic Range Microphone is a high sound pressure level (SPL), ultralow noise, low power, digital output, bottom ported omnidirectional MEMS microphone. This microphone clips at 133 dB SPL, which is useful for clearly capturing audio in loud environments. The ADMP621 consists of a MEMS microphone element and an impedance converter amplifier followed by a fourth-order Σ-Δ modulator. The digital interface allows the pulse density modulated (PDM) output of two microphones to be time multiplexed on a single data line using a single clock. The ADMP621 is pin compatible with the ADMP421 and ADMP521 microphones, providing an easy upgrade path. The ADMP621 has a high SNR of 65dBA and sensitivity of −46dBFS. The ADMP621 has an extended wideband frequency response, resulting in natural sound with high intelligibility. Low current consumption and a sleep mode with less than 5.5μA of current consumption enables long battery life for portable applications.
Analog Devices ADA466x Precision CMOS Operational Amplifiers are dual, precision, rail-to-rail input/output amplifier optimized for low power, high bandwidth, and wide operating supply voltage range applications. The ADA466x performance is guaranteed at 3.0V, 10V, and 18V power supply voltages. It is an excellent selection for applications that use single-ended supplies of 3.3V, 5V, 10V, 12V and 15V, and dual supplies of ±2.5V, ±3.3V, and ±5V. It uses the Analog Devices, Inc., patented DigiTrim® trimming technique, which achieves low offset voltage. Additionally, the unique design architecture of the ADA466x allows it to have excellent power supply rejection, common-mode rejection, and offset voltage when operating in the common-mode voltage range of −VSY + 1.5V to +VSY − 1.5V.
Analog Devices AD8229HDZ ultra-low noise instrumentation
amplifier measures small signals in the presence of large common-mode
voltages and high temperatures. AD8229HDZ’s design architecture
compensates for the low VBE
voltages at high temperatures. The process is dielectrically isolated
to avoid leakage currents at high temperatures. It delivers industry
leading 1 nV/√Hz input noise performance, and is one of the industry's
fastest instrumentation amplifiers. The current feedback architecture is
designed for high bandwidth at high gain. The high CMRR of the
AD8229HDZ prevents unwanted signals from corrupting the acquisition.
Designed for excellent distortion performance in temperatures up to
210°C, AD8229HDZ is ideally suited for demanding applications such as
vibration analysis, exhaust gas measurements, down-hole instrumentation,
and harsh environment data acquisition.
Evaluation hardware for the ADSP-CM40x provides a low-cost hardware
solution for development. The ADSP-CM403F EZ-KIT Lite and the
ADSP-CM408F EZ-KIT Lite include all hardware necessary to immediately
begin evaluation. Other development boards can be purchased without a
Analog Devices ADSP-CM40x Mixed Signal Control Processors utilize the ARM® Cortex®-M4 processor core, integrated with high precision ADCs, digital accelerators, filters, SRAM, flash memories, and a rich set of peripherals. The ADSP-CM40x processors are suitable for a wide myriad of embedded applications requiring high performance real-time control and analog conversion, such as motor control and industrial applications.
Analog Devices AD5687/AD5687R Dual 16-/12-Bit nanoDAC+™ are low power, dual, 16-/12-bit, buffered voltage output digital-to-analog converters (DACs). The devices include a gain select pin giving a full-scale output of 2.5V (gain = 1) or 5V (gain = 2). The AD5687/AD5687R operate from a single 2.7V to 5.5V supply, are guaranteed monotonic by design, and exhibit less than 0.1% FSR gain error and 1.5mV offset error performance. Devices are available in a 3mm × 3mm LFCSP and a TSSOP package. The AD5687/AD8687R also incorporate a power-on reset circuit and a RSTSEL pin that ensure that the DAC outputs power up to zero scale or midscale and remain there until a valid write takes place. Each part contains a per channel power-down feature that reduces the current consumption of the device to 4μA at 3V while in power-down mode. The AD5687/AD5687R use a versatile serial peripheral interface that operates at clock rates up to 50MHz. Each device contains a VLOGIC pin that is intended for 1.8V/3V/5V logic.
Analog Devices ADM3485E Low Power Data Transceiver provides ±15kV ESD protection and is suitable for half-duplex communication on multipoint bus transmission lines. The ADM3485E is designed for balanced data transmission and complies with TIA/EIA standards RS-485 and RS-422. The ADM3485E is a half-duplex transceiver that shares differential lines and has separate enable inputs for the driver and the receiver. The devices have a 12kΩ receiver input impedance, which allows up to 32 transceivers on a bus. Because only one driver should be enabled at any time, the output of a disabled or powered-down driver is tristated to avoid overloading the bus. The receiver has a fail-safe feature that ensures a logic high output when the inputs are floating. Excessive power dissipation caused by bus contention or by output shorting is prevented with a thermal shutdown circuit.
Analog Devices ADL5511 RF RMS Detector is an RF envelope and TruPwr™ rms detector. The envelope output voltage is presented as a voltage that is proportional to the envelope of the input signal. The rms output voltage is independent of the peak-to-average ratio of the input signal. The rms output is a linear-in-V/V voltage with a conversion gain of 1.9V/Vrms at 900MHz. The envelope output has a conversion gain of 1.46V/V at 900MHz and is referenced to an internal 1.1V reference voltage, which is available on the EREF pin. The ADL5511 can operate from dc to 6GHz on signals with envelope bandwidths up to 130MHz. The extracted envelope can be used for RF power amplifier (PA) linearization and efficiency enhancements and the rms output can be used for rms power measurement. The high rms accuracy and fast envelope response are particularly useful for envelope detection and power measurement of broadband, high peak-to-average signals that are used in CDMA2000, W-CDMA, and LTE systems.
Analog Devices AD5689 Dual 16-Bit nanoDAC+ is a member of the nanoDAC+™ family low power, dual, 16-bit, buffered voltage output digital-to-analog converter (DAC). It includes a gain select pin giving a full-scale output of 2.5V (gain = 1) or 5V (gain = 2). The AD5689 operates from a single 2.7V to 5.5V supply, are guaranteed monotonic by design, and exhibit less than 0.1% FSR gain error and 1.5mV offset error performance. It also incorporate a power-on reset circuit and a RSTSEL pin that ensures that the DAC outputs power up to zero scale or midscale and remain there until a valid write takes place. Each contains a per channel power-down feature that reduces the current consumption of the device to 4μA at 3V while in power-down mode.
Analog Devices ADP5033 Dual Buck Regulators combine two high performance buck regulators and two low dropout regulators (LDO) in a tiny, 16-ball, 2mm × 2mm WLCSP to meet demanding performance and board space requirements. The high switching frequency of the buck regulators enables tiny multilayer external components and minimizes the board space. The two bucks operate out of phase to reduce the input capacitor requirement and noise. The low quiescent current, low dropout voltage, and wide input voltage range of the ADP5033 LDO extend the battery life of portable devices. The ADP5033 LDOs maintain power supply rejection greater than 60dB for frequencies as high as 10kHz while operating with a low headroom voltage.
Analog Devices EVAL-AD7980SDZ full-featured evaluation kit for AD7980 analog-to-digital converters is designed to demonstrate the ADC's performance and provide an easy to understand interface for a variety of system applications. This ADI evaluation kit operates in stand alone mode or in conjunction with EVAL-SDP-CB1Z System Development Platform. When operated with the System Development Platform, software is provided enabling the user to perform a detailed analysis of the ADC's performance.
Analog Devices ADP5037 800mA Buck Regulators combine two high-performance buck regulators and two low dropout (LDO) regulators in a small, 24-lead 4mm × 4mm LFCSP to meet demanding performance and board space requirements. The high switching frequency of this ADI device's buck regulators enables tiny multilayer external components and minimizes the board space. The two buck regulators operate out of phase to reduce the input capacitor requirement. The low quiescent current, low dropout voltage, and wide input voltage range of the ADP5037 LDOs extend the battery life of portable devices. The ADP5037 LDOs maintain power supply rejection greater than 60 dB for frequencies as high as 10 kHz while operating with a low headroom voltage.
Analog Devices ADuM4160 USB Digital Isolator is a USB port isolator based on iCoupler® technology. ADI ADuM4160 combines high speed CMOS and monolithic air core transformer technology to provide outstanding performance characteristics. The device is easily integrated with low and full speed USB-compatible peripheral devices. ADuM4160 provides mechanisms for detecting the direction of data flow and control over the state of the output buffers. Data direction is determined on a packet-by-packet basis. ADI ADuM4160 uses the edge detection based iCoupler technology in conjunction with internal logic to implement a transparent, easily configured, upstream facing port isolator. Isolating an upstream facing port provides several advantages in simplicity, power management, and robust operation. The isolator has propagation delay comparable to that of a standard hub and cable. It operates with the supply voltage on either side ranging from 3.1 V to 5.5 V, allowing connection directly to VBUS by internally regulating the voltage to the signaling level. ADuM4160 provides isolated control of the pull-up resistor to allow the peripheral to control connection timing.
Analog Devices broad product portfolio supports a wide range of markets. Select Applications below to learn more.